(Click on this button to add checked items to your shopping cart.)
KX3 All Mode 160 - 6 M
Transceiver
Tested
Click
Here for Shipping Status
KX3-K KX3 160-6 M Xcvr (Modular Kit)
SSB, CW, Data (RTTY, PSK), AM, FM
899.95
KX3
Info Page (pictures, videos and spec's.)
KX3-F KX3 160-6 M Transceiver
(Factory Assembled and Tested)
SSB, CW, Data (RTTY, PSK), AM, FM
999.95
KX3
Info Page (pictures, videos and spec's.) Options ordered for
factory assembled KX3's will be factory installed at the time of build, if
available.
The KX3
supports USB and RS-232 control interfaces via its ACC1 3.5mm jack and the
appropriate interface cable. A KXUSB interface cable for USB is supplied
standard with the KX3. If you prefer the RS-232 interface, check the box
below to exchange the supplied KXUSB for the KXSER cable (3.5MM to DB9-F).
KXSER (3.5mm to DB9-F): Exchange
Cable 3.5mm to RS232 DB9-F for KX3. (No charge for exchanging KXUSB
for KXSER)
0.00
KXSERa (3.5mm to DB9-F): Extra
Cable
29.95
KXUSBa (USB to 3.5mm): Extra Cable
29.95
KX3
Options
*Options listed below are
not included with the KX3.
MH3 Hand Microphone for the KX3 with Up/Dn Buttons
Compact hand mic with coiled cord, custom-designed for the KX3. Includes UP/DN VFO controls and space-saving right-angle plug.
MH3 Manual (pdf)
59.95
Proset-K2
Boom Headset
Comes with
3.5mm stereo headphone and mono microphone connectors that plug directly
into the KX3. (Also includes 1/4" headphone and 8 pin adapters for
the K2/K3). You may use the KX3 XMIT button or VOX for TX PTT.
165.00
KX3-PCKT Accessory Cable Set
The KX3-PCKT cable
set interfaces between the Elecraft KX3 and personal computers, and
provides convenient connection to an external foot switch and RF power
amplifier. KX3-PCKT
Instructions
19.95
KX3-PCKT Individual Cable Extras
(E980229) Transmit Audio Cable (E980230) Receive Audio Cable (E980231) I/Q Output Cable (E980232) ACC2 IO Module
Power Cable Extras (E850524) Extra KX3 Power Cable, Right
Angle
KXFL3 dual-Passband Roofing Filter
Adds high-performance, hand-trimmed roofing filters ahead of the receiver's DSP subsystem, resulting in improved close-spaced dynamic range in CW, data, and SSB modes. 500 Hz/1500 Hz matched analog filters (1000/3000 Hz equivalent IF passband in I and Q channels).
129.95
KXAT3 Internal, 20-W
Automatic Antenna Tuner
8-inductor/8-capacitor L-network provides very wide matching range and fast tuning. Multiple per-band memories provide nearly instant re-tune. Operates even in receive, improving selectivity ahead of receiver. Includes filter elements to optimize AM broadcast band receive (0.5-1.6
MHz).
169.95
KXPD3 Precision Iambic Keyer Paddle
Lightweight, precision paddle attaches directly to the KX3 with two captive thumbscrews. Adjustable spacing using provided hex wrenches.
Menu-selectable dot/dash paddle reverse, hand key mode, and two iambic modes.
129.95
KXPD3MDKT Upgrade Kit for the KXPD3
The upgrade kit contains two replacement springs of
differing tension, a new set of screw-in contacts with
rounded tips and a new set of stainless steel stationary contacts.
0.00
(Shipping within 7 to 10 days)
* When ordering only the upgrade, select
Check/Money Order as payment option, and enter FREE as the check number.
KXBC3 Internal NiMH Charger / Real-Time Clock
Safely
and automatically charges 8 NiMH cells in the KX3's internal 8-AA battery
pack from an external 13.8V supply. Charge time varies depending on cell
capacity and depth of discharge; 8 hours typical. Includes real-time
clock, providing time display and alarm.Minimum Charging Voltage: 13.8v Charging Current: 200 mA
59.95
XG50
Kit (Simple 49.380 MHz Signal Source)
The Elecraft XG50 is a simple 49.380 MHz signal source specifically designed for use with the KX3 Extended VFO Temperature Compensation Procedure.
See App
Note.
39.95
BNC-RA Male-Female
Right Angle BNC
Conveniently
routes the KX3 antenna cable parallel to the side of the KX3.
6.95
BNC-BP BNC
Male to Stackable Binding Posts
Easily
attach a portable wire antenna with your KX3. Also provides a convenient
connection for a counter-poise.
9.95
KHAT - Elecraft Logo Hat Navy
Blue Hat with White Elecraft Logo.
12.00
Buddipole Portable Antennas (Click here for
special pricing with KX3)
Click
Here for the KXPA100 Order Page
(Click on this button to add checked items to your shopping cart.)
KPA500
160 - 6M, Solid State, Automatic Band Switching Linear
Amplifier
(FCC
ID: UTR-KPA500)
KPA500-K
500W Linear Amplifier, Kit
160-6M, Solid State, Freq.
Sensing Auto Band Switching Amplifier
Same size as the K3, 26 lbs., 12 kg
Full QRQ Break-in; 100-125V, 200-250V
(Works with any radio that supplies PTT to GND)
Manual
eHam
reviews
2099.95
KPA500-F
500W Linear Amplifier, Factory
Assembled
160-6M, Solid State, Freq.
Sensing Auto Band Switching Amplifier
Same size as the K3, 26 lbs., 12 kg
Full QRQ Break-in; 100-125V, 200-250V
(Works with any radio that supplies PTT to GND)
Manual
eHam
reviews
2299.95
Price
KPAK3AUX Optional
KPA500 to K3 AUX Cable
K3
to amp keying, band data, amp band buttons set K3 band. Amp
operate/standby status sent to K3 - allows K3 to switch between two power
levels. Includes cable, Y cable expansion
adapter, and TX keying line interrupter.) Manual
w/ Pictures (pdf)
E980190 Extra
DB15 Y- Cable ($9.95 )
34.95
KPA500
120V and 220V Power Cords
PWR-EU2P IEC-European (Schuko) Power Cord
w/fuses
Exchange
(Only
one PWR-EU2P or the PWR-US240 may be exchanged for the IEC US 120V cord
that comes with the KPA500)
0.00
No charge exchange
PWR-US240 IEC-U.S. 240V Power Cord
w/fuses
( NEMA 6-15P suitable for 6-15R and 6-20R receptacles)
Exchange
(Only
one PWR-EU2P or the PWR-US240 may be exchanged for the IEC US 120V cord
that comes with the KPA500)
0.00
No charge exchange
PWR-EU2Pa Extra IEC-European
(Schuko) Power Cord w/fuses
15.95
PWR-USa Extra IEC
120V U.S Power Cord w/fuses. 14 ga.
15.95
PWR-US240a Extra IEC-U.S. 240V Power Cord
w/fuses
( NEMA 6-15P suitable for 6-15R and 6-20R receptacles)
15.95
(Click on this button to add checked items to your shopping cart.)
KAT500
High Power Autotuner
KAT500-K High Power ATU, Kit
Matches
approx 10:1 SWR at 500-600 W,A KXUSB is supplied standard with the KAT500.
649.95
KAT500-F High Power ATU, Factory Assembled
Matches
approx 10:1 SWR at 500-600 W,
3:1
SWR at 1000 W.A KXUSB is supplied standard with the KAT500.
699.95
E850463 Optional KAT500 to
KPA500 Cable
KAT500
to KPA500 cable. Provides band data to KAT500 for band change
prior to TX,, and feeds through KPAK3AUX cable data from the K3 to
the KPA500. Typically used in addition to the KPAK3AUX cable
from the K3 to route band data, keying and AUXBUS data through the
KAT500 to the KPA500. (The KAT500 has AUX Cable IN and OUT
connections.)
This
is the same 15 pin cable as is contained in the KPAP3AUX cable set
(see above, under the KPA500). That set also includes a Y cable
expansion adapter and a TX line keying interrupt adapter for the
K3 to KPA500 link.
24.95
E980190 9.95
KXSER (3.5mm to DB9-F): Exchange
Cable
(No charge for exchanging KXUSB for KXSER)
0.0
KXSERa (3.5mm to DB9-F): Extra
Cable
29.95
KXUSBa (USB to 3.5mm): Extra Cable
29.95
(Click on this button to add checked items to your shopping cart.)
K3
High Performance 160 - 6M Transceiver
New
K3 orders are now being built immediately to order. See our Shipping
Status page for the latest information.
K3
- Kit
Price
K3
- Factory Assembled
Price
K3/10
10
W
Transceiver, Kit 1,599.95
K3/10-F
10 W
Transceiver, Assembled1,799.95
K3/100
100 W
Transceiver, Kit 2,099.95
K3/100-F 100 W
Transceiver, Assembled2,349.95
K3 Options -- Factory Assembled / Installed
P3-K DSP Panadapter
Kit for the K3 and other rigs
Requires
KXV3 or KXV3a to supply the K3's IF output to the
P3.
699.95
P3-F DSP Panadapter
(Assembled) for the K3 and other rigs
Requires
KXV3 or KXV3a to supply the K3's IF output to the P3.
749.95
P3SVGA Video
Adapter / FFT Processor add-in for the P3
(Now shipping) 269.95
P3SVGA Video
Adapter / FFT Processor add-in for the P3
(Now shipping) 269.95
KAT3 Internal ATU with 2nd Ant. Jack
for the K3 Kit299.95
KAT3-F Internal ATU with 2nd Ant. Jack for the K3-F349.95
KRX3 High Performance Subreceiver for the K3
Kit (incl. 2.7 kHz
filter)
599.95
KRX3-F High Performance Subreceiver for the K3-F (incl. 2.7 kHz
filter)
679.95
K144XV-K Internal
2 M 10w Module Kit for the K3
Kit
Requires
a KXV3A for internal XV conn. and switching.
--
IMPORTANT:
Check
one: For
a K3/10 For
a K3/100
K144RFLK recommended for best SSB/CW stability on 144 Mhz See below
For
FM operation, KFL3B-FM filter must be installed in the K3.
K144XV
Manual
KXSER (RS-232) Cable - Exchange (No charge exchange for the
supplied KXUSB cable)
299.95
K144XV-F Internal
2 M 10w Module for the K3-F for the K3-F
Requires
a KXV3A for internal XV conn. and switching.
--
IMPORTANT:
Check
one: For
a K3/10 For
a K3/100
K144RFLK recommended for best SSB/CW stability on 144 Mhz See below
For
FM operation, KFL3B-FM filter must be installed in the K3.
K144XV
Manual
KXSER (RS-232) Cable - Exchange (No charge exchange for the
supplied KXUSB cable)
359.95
KPA3 Internal 100 W Upgrade for K3/10
Kit
499.95
KPA3-F Internal 100 W Upgrade for K3/10
549.95
K3
Options - For both kit and factory assembled K3s
K144RFLK
K144XV Reference Lock BoardLocks K144XV Oscillators to
K3's high accuracy master TCXO
Recommended for best stability on 144 Mhz manual 89.95
KXV3A RX Ant., IF Out and Xverter Interface
The
'A' version adds
internal I/O and switching for K144XV.
(Also
see XV's)
119.95
KXV3A_UPGR Upgrade from
existing KXV3 to KXV3A Return
of old KXV3 required after receipt of KXV3A
69.95
KTCXO3-1
TCXO (0.1 ppm typ) High Stability Ref. Osc.
99.95
External Reference Input for the K3. Locks the K3 to an external 10
MHz Reference. manual 99.95
KDVR3 Digital Voice Recorder
139.95
KBPF3 General
Coverage RX Bandpass Module Adds
coverage outside of ham bands. Install on main and/or sub RX.
159.95
(Connects to the RX IN/OUT conn. on the KXV3.)
Uses two BNC-MM
connectors (INCLUDED) Requires K3 KXV3 option
(above) manual
149.95
KUSB USB (Universal Serial Bus) Adapter for the K3
(Now uses the FTDI chipset - 8/4/10)
Click
here for the KUSB Window, Mac and Linux Drivers
39.95
K3SSKT Stainless
Steel Exterior H/W Kit Black
stainless steel K3 exterior screw, nut and h/w set (marine, extreme
humidity etc.)
19.95
KPCA-F Extra Power Cable, 5 ft, Assembled with APP
Conn, un-terminated at
other end.
(This
cable is supplied with assembled K3-F radios. K3 kits include the unassembled
version of this cable.)
14.95
Microphones
MH2 Hand Microphone (For the K3/K2) instructions 59.95
Proset-K2
Boom Headset
165.00
External Transverters for 144, 222 and 432 Mhz (See Below)
Buddipole Portable Antennas (See Below)
K3
Crystal Filters
A 2.7 kHz 5-pole filter is
included with each K3 and each KRX3.
There
are 5 filter positions per K3 and per KRX3. The 2.7 kHz filter
uses one of these positions.
If
you need more than one of any filter (for the KRX3 etc), check
it here and then increase the qty in your shopping cart prior to checkout.
CW
/ Data
SSB / AM /
FM
KFL3A-200 200 Hz, 5-pole 89.95
KFL3A-1.8K 1.8 kHz, 8-pole * 139.95
KFL3A-250 250 Hz, 8-pole 139.95
KFL3A-2.1K 2.1 kHz, 8-pole * 139.95
KFL3A-400 400 Hz, 8-pole 139.95
KFL3A-2.8K 2.8 kHz, 8-pole *
139.95
KFL3A-500 500 Hz, 5-pole 89.95
KFL3A-6K 6 kHz AM / ESSB, 8-pole
(req'd
for AM) ** 139.95
KFL3A-1.0K 1 kHz, 8-pole 139.95
KFL3B-FM 13 kHz FM
(required
for FM) ** 139.95
KFL3A-2.8_2.7sw 2.8 kHz 8-pole
REPLACEMENT for the standard 2.7 kHz 5 -pole filter
(New K3 and KRX3 orders only) 129.95
KFLMATCH - Matching of 5 pole filter pair offsets to 40 Hz.
(200 Hz, 500 Hz and 2.7 kHz 5-pole filters only)
All
8-pole and 5-pole filter plots What filters should I buy? -
Filter Notes from Wayne and Eric
For same operating frequency
diversity receive usage with K3 and KRX3 locked together. Set the K3 offset
menu for both filters equal and to the nearest 10Hz offset
approximately half way between their marked offset frequencies.
Only applies to our 5 pole filters, 200 Hz, 500 Hz and 2.7 kHz,
which have non-zero offsets.
Note: Best if both
filters to be matched are ordered at the same time. We
will try to accommodate matching to 5 pole filters already shipped
(8 pole filters all have a nominal 0 offset) but
we can only guarantee an offset match within 40 Hz if both filters are ordered at
the same time, due to batch to batch manufacturing frequency
changes. The K3 menu filter offset for both filters can then be set equally to the midpoint between their
offsets.
19.95
*
On SSB the K3 should transmit through the widest SSB filter
available, typically 2.7 or 2.8 kHz. (You can receive on any
filter.) All K3's must have at least a 2.7 or 2.8 kHz SSB
filter installed. (2.7 kHz is included with the base K3.) For ESSB, TX can be set to use the 6 kHz
filter (if installed) and b/w can then be set by the DSP.
** AM and FM bandwidth filters are required on
the main K3 TX/RX board for TX in AM and FM modes. (Only one AM filter is required for AM TX/RX,
and one FM filter for FM TX/RX.) All filters can be used for RX in any mode.
KHAT - Elecraft Logo Hat Navy
Blue Hat with White Elecraft Logo.
12.00
K3
Replacement Manuals
K3 Owners (Operating) Manual Printed (included
with new K3s) 19.95
K3 Assembly Manual Printed (included with new K3
kits) 29.95
Note:
All K3 Manuals are available for FREE download via our Manual
Download Page
K3
Parts and Mod Kits Order Page
(Click on this button to add checked items to your shopping cart.)
K3-Remote
Internet
Remote 'Twin' Control of the K3 with real knobs and buttons for a
100% real time radio feel.
K3/0 Remote Control Head for the K3-Remote / RemoteRig system
The K3/0
appears identical to the K3 in size and function and with an identical front
panel, but does not include the internal RF or DSP components. When paired
with the RemoteRig unit, it fully reproduces all K3 functions and controls
with VoiP audio over the internet via the RemoteRig set. All local K3/0 knob
motion (VFOs etc) and button presses are immediately reflected on the remote
K3. The local K3/0 display reflects exactly what is displayed on the remote
K3. Audio from the remote K3 is reproduced via the K3/0 speaker and the
microphone plugs into the front of the K3/0. No Computer is required during
normal operation. (A computer is required for initial setup configuration.)
Note:
Requires
the RRIGSET RemoteRig 1258MKII
Order
the RRK0CBL cable set (below) for the local K3/0 to RemoteRig unit
connections.
Order
RRMTCBL cable set (below) for remotely controlled K3 to remote
RemoteRig unit connections.
Both
local and remote K3s must be running K3 f/w 4.47 or later for proper
K3-Remote operation.
695.95
RRIGSET RemoteRig 1258MKII
SET Dual
rx capable remote control set with
12V pwr supply for the local end.
The
RemoteRig RRC-1258MkII SET is developed specially for
remote control of Amateur Radio stations via the Internet, in a user
friendly and cost-effective way.
The
RemoteRig units are used in pairs, one is connected to the
remote K3 and the other is connected to the local control K3/0 or K3.
The
system is unique in that no PC is needed -both voice and data
communication are handled by the two RemoteRig units. The RRC-1258MkII-S can
be configured to work together with the K3/0 controlling a remote K3, or
with a regular K3 controlling the remote K3 over your local network or the internet. For CW, The
RemoteRig provides Iambic (A/B) keyer with local sidetone and speed control.
It also uses a special internet protocol to eliminate CW jitter from
network latencies.
499.95
RRIGCON RemoteRig 1258MKII
Control Unit Only
For control of another K3 already setup for remote operation.
289.95
RRK0CBL
49.95
R RMTCBL
49.95
RRK3CBL Cable set for the local 'terminal mode' K3 to RemoteRig unit
connections (For use with a regular K3 as the control unit instead of
a K3/0. (Requires K3 f/w 4.47 or later for proper K3-Remote operation.)
49.95
(Click on this button to add checked items to your shopping cart.)
K2
- The Classic HF Transceiver - Full Kit
Price
Price
K2
HF Transceiver
759. 95
KIO2
RS-232 Serial Interface
99.95
KPA100
100W Option(K2 + KPA100 = K2/100)
399. 95 KUSB
USB Adapter for the KIO2 or KPA100
(Now uses the FTDI chipset - 8/4/10)
Click
here for KUSB Window, Mac and Linux Drivers
39.95
KSB2
SSB Option
129. 95
KBT2
Internal Battery Kit
79.95
K160RX
160M Option
39. 95
KBT2-X
(KBT2 w/o Battery)
49.95
Manual
99. 95
BATT
Replacement Battery
30.95
NOTE: If you want to add the K60XV to an existing
K2, Click Here for
the K60XV upgrade order page
KAT100-1
100W Ext. ATU
249.95
KNB2
Noise Blanker
59. 95
KAT100-2
100W ATU w / EC2 Panels (must
also order EC2)
229.95
KDSP2
Advanced Internal DSP Filter
/ Clock
/ Clock
249. 95
KAT100PNL
Converts KAT100-1 to -2
39.95
KAF2
Audio Filter
89. 95
EC2
Blank Project Enclosure
79.95
KAT2
20W Internal ATU
179. 95
ETS15
1.5" Tilt Stand for EC2, KAT100
14.95
FDIMP
6. 95
ETS2
Std 3" Tilt Stand for EC2
14.95
KPCA-F Power Cable, 5 ft, Assembled with APP Conn ,
un-terminated at other end. (K2
kits get the unassembled version of this cable.)14.95 KXPD1-K2
Mounting bracket attaches KXPD1 to the K2 tilt bail.65.95
Microphones for
the K2, K3
MH2 Hand Microphone (For K2 and K3) instructions 59.95
Proset-K2
Boom Headset for the K2, K3 (Heil)165.00
KHAT - Elecraft Logo Hat Navy
Blue Hat with White Elecraft Logo.
12.00
(Click on this button to add checked items to your shopping cart.)
K1
QRP Transceiver Kit and Accessories
Price
Price
K1-4
Four-Band 5W CW Xcvr
Includes: 40, 30, 20 and 17 or 15M (chosen at
build time)
399.95
KFL1-4
Additional 4 Band Module
Includes: 40, 30, 20 and 17 or 15M (chosen at
build time)
149.95
K1-2
Two-Band 5W CW Xcvr
299.95
KFL1-2
Additional 2 Band Module
79.95
Note:
Both
the K1-2 and the KFL1-2 require you to choose two bands.
Check two boxes: 80M 40M
30M
20M
17M
15M
KAT1
Internal ATU for the K1
129.95
KTS1
Wide Range Tlt Stand
39.95
KNB1
Noise Blanker
49.95
FDIMP
Finger Dimple for K1 & K2
6.95
KBT1
Internal Battery Adapter
49.95
BNC-BP BNC
Male to Stackable Binding Posts
9.95
K1BKLTKIT
K1LCD Backlight Mod Kit for built K1s picture
39.95
K1BKLTKIT-X
K1LCD Backlight Mod Kit for unbuilt K1s
picture
29.95
(Click on this button to add checked items to your shopping cart.)
KX1
Ultra-Portable CW QRP Transceiver Kit
Price
Price
KX1
Ultra-Portable CW Xcvr Kit (20+40 m)299.95 KXPD1-K2
Mounting bracket also attaches KXPD1 to the K2 tilt bail.65.95
KXB3080
30/80 M Adapter for the KX189.95 BNC-BP BNC
Male to Stackable Binding Posts 9.95
KXAT1
Internal Auto. Ant. Tuner129.95
KXPD1
Plug-in Keyer Paddle69.95
(Click on this button to add checked items to your shopping cart.)
T1 Miniature Stand-Alone ATU
and Accessories
Price
Price
T1-K 139.95
DL1
20W Dummy Load with RF detector
25.95
T1-A
159.95
BL2
250W 1:1 & 4:1 (switched) Balun manual
datasheet
39.95
T1-FT817 18",
shielded cable for auto
band switching from FT-817 to T1.
59.95
BNC-MM
Male-Male BNC Connector
6.95
(Click on this button to add checked items to your shopping cart.)
Price
KRC2
Band Decoder for the K2, K3 and Most HF Rigs
Price
XV50
6 Meter Transverter
399.95
KRC2
Band Decoder and Controller
159.95
XV144
2 Meter Transverter
399.95
KRC 2ACC
Band Decoder and Controller
with full CW feedback
179.95
XV222
222 MHz Transverter
399.95
KRC 2ACCMDKT
Converts a KRC2 to a KRC2ACC
20.95
XV432
432 MHz Transverter Includes Helical Filters for excellent
image rejection.
399.95 KPCA-F Power Cable, 5 ft, Assembled with APP Conn ,
un-terminated at other end. ( XV
kits get the unassembled version of this cable.)14.95
XVOVN
Crystal Oven for XV Series 49.95 PR6 Low Noise 6M GaAs FET Preamp (0.5 dB typ) for the
K3 and all other 6M Rigsmanual (Integrates directly with the RX IN/OUT connectors on
the KXV3.) On K3s the PR6 requires the KXV3 option.
149.95
HIACC432
High Accuracy L.O. Crystal for XV432 (Requires
XVOVN Option) 39.95
(Click on this button to add checked items to your shopping cart.)
W2
Wattmeter / SWR Bridge
W2-K
Wattmeter / SWR Bridge - Kit Includes
one directional coupler - choose power/freq. range below. (Up to Two
couplers supported per W2.)
A KXUSB interface cable for USB is supplied
standard with the W2. If you prefer the RS-232 interface, check the box
below to exchange the supplied KXUSB for the KXSER cable (3.5MM to DB9-F).
KXSER (RS-232) Cable - Exchange (No charge exchange for the
supplied KXUSB cable)
239.95 W2-A
Wattmeter / SWR Bridge -
Factory Assembled
Includes
one directional coupler - choose power/freq. range below. (Up to Two
couplers supported per W2.)
A KXUSB interface cable for USB is supplied
standard with the W2. If you prefer the RS-232 interface, check the box
below to exchange the supplied KXUSB for the KXSER cable (3.5MM to DB9-F).
KXSER (RS-232) Cable - Exchange (No charge exchange for the
supplied KXUSB cable)
299.95
Directional Couplers
for the W2
First
Directional Coupler Supplied with W2 (Must select one) 2nd
Optional Directional Coupler
DCHF-200
1.8-54 MHz, 0.1-
200W n/c DCHF-200a
1.8-54 MHz, 0.1- 200W
additional coupler 99.95
DCHF-2000
1.8-54 MHz, 1- 2000W n/c DCHF-2000a
1.8-54 MHz, 1- 2000W
additional coupler 99.95
DCV/U-200
144-450 MHz, .1- 200W n/c DCV/U-200 a
144-450 MHz, .1- 200W additional coupler 99.95
1.5 MHz through 1400 MHz)
Price
Click
Image for larger version
XG3
RF Signal Source (assembled)
manual 1.5-200 MHz
with calibrated output levels: -107, -73, -33 and 0 dBm. Rich in harmonics
to 1400 MHz. Frequencies
programmed into memories above 200 MHz fundamental will automatically
calculate the fundamental needed to generate the desired harmonic. 1 2 frequency
memories, computer controllable.
Dimensions:
4.3
x 2.5 x 0.8" A KXUSB interface cable for USB is supplied
standard with the XG3. If you prefer the RS-232 interface, check the box
below to exchange the supplied KXUSB for the KXSER cable (3.5MM to DB9-F).
KXSER (RS-232) Cable - Exchange (No charge exchange for the
supplied KXUSB cable)
179.95
AT1
manual
datasheet
Excellent Match for the XG3, Adds 1 dB level increments. (also see BNC-MM)
59.95
BNC-MM
Male-Male BNC Connector
6.95
Mini-Module Kits
Price
Price
W1
LED Bar-graph Wattmeter / SWR Bridge
manual
datasheet
89.95
XG2 3 Band 1-uV
/ 50-uV Receiver Test
Oscillator (80, 40 & 20M)
manual datasheet
79.95
W1SERKT
W1 Serial Cable Kit
14.95
DL1 20W Dummy Load with RF detector
manual
datasheet
25.95
AF1
manual
datasheet
59.95
BL2
250W 1:1 & 4:1 (switched) Balun manual
datasheet
39.95
AT1
manual
datasheet
59.95
CP1 Directional Coupler, 1-30 MHz
manual datasheet
39.95
N-gen
Wideband Noise Generator, 100 kHz-500 MHz
manual datasheet
59.95
BNC-MM
Male-Male BNC Connector
6.95
2T-gen
2-Tone
Test Generator (700, 1900 Hz)
manual datasheet
69.95
XG50
Kit (Simple 49.380 MHz Signal Source)
See KX3
App Note
39.95
(Click on this button to add checked items to your shopping cart.)
Buddipole Portable Antenna Systems
Price
Price
Deluxe
Buddipole Antenna Pkg. (
399.00
Extra Coil Clips (3)
12.00
Buddistick
Vertical Portable Antenna
139.00
Deluxe Vertical Antenna Universal
Clamp
24.50
Deluxe
Buddistick Vertical Pkg. Note:
Customer choice of: Optional
Mini Tripod(Chose one).
175.00
Replacement Stainless Steel Telescopic
Whip
12.00
Buddistick⢠Tripod
24.50
SPECIAL!
Important:
Antenna and Radio much be purchased at the same time for this package
discount to apply.
-- Radio and
Tech. Books - Click Here
-- Spare
Parts, Firmware and Mod Kits - Click Here
(Click on this button to add checked items to your shopping cart.)
®
Waters
& Stanton PLC
and 